MPLS TE Autotunnel Primary, Backup and Mesh Group for L3VPN

« 2023 Jan 24 »

What are the different types of MPLS TE autotunnels?

The autotunnel feature reduces the administrative tasks related to MPLS Traffic Engineering (TE) tunnel configurations. A variety of MPLS TE tunnels can be dynamically established using autotunnels instead of manually creating each individual tunnel interface. The following summary provides an overview of the three types of autotunnels.

MPLS TE autotunnels explained in summary autotunnel primary, backup and mesh with mesh-group ID

The features described above are listed in the following router output. As visible, each of the autotunnel features has to be enabled separately and the number of created autotunnels can be tracked using the following show command.

R3#show mpls traffic-eng tunnels brief
Signalling Summary:
    LSP Tunnels Process:            running
    Passive LSP Listener:           running
    RSVP Process:                   running
    Forwarding:                     enabled
    auto-tunnel:
        backup Disabled (0 ), id-range:65436-65535          « Autotunnel Backup
        onehop Enabled  (2 ), id-range:50-55                « Autotunnel Primary
        mesh   Disabled (0 ), id-range:64336-65335          « Autotunnel Mesh

    Periodic reoptimization:        every 3600 seconds, next in 1115 seconds
    Periodic FRR Promotion:         Not Running
    Periodic auto-tunnel:         
        primary establish scan:     every 10 seconds, next in 5 seconds
        primary rm active scan:     disabled
    Periodic auto-bw collection:    every 300 seconds, next in 215 seconds
TUNNEL NAME                      DESTINATION      UP IF      DOWN IF    STATE/PROT
R3_t50                           4.4.4.4          -         Gi0/1     up/up     
R3_t51                           2.2.2.2          -         Gi0/0     up/up     
R2_t50                           3.3.3.3          Gi0/0      -          up/up     
R4_t50                           3.3.3.3          Gi0/1      -          up/up     
Displayed 2 (of 2) heads, 0 (of 0) midpoints, 2 (of 2) tails

Configuring MPLS TE autotunnel primary

In the following example topology MPLS TE autotunnel primary is configured on each label switching router (LSR) in the Service Provider MPLS L3VPN network. The autotunnel primary feature instructs a router to dynamically create a one-hop tunnel with each of its directly adjacent neighbors that have MPLS TE enabled. In other words, if two directly connected routers have MPLS Traffic Engineering enabled, they will dynamically create a single-hop primary tunnel.

Thus, R2 has an autotunnel with R3, R3 has an autotunnel with R2 and with R4, and so on. To enable a label switched path (LSP) between PE R2 and PE R6 the autotunnels have LDP enabled with the command mpls traffic-eng auto-tunnel primary config mpls ip. As a result, targeted-LDP neighborships are formed between each adjacent LSR to exchange label bindings.

MPLS Traffic Engineering auto-tunnel primary configuration with Layer-3 VPN network architecture

Configuration:

R2 (PE)
    R2#show run | sec ^mpls
    mpls label range 200 299
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel primary onehop
    mpls traffic-eng auto-tunnel primary config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel primary config mpls ip
    mpls traffic-eng auto-tunnel primary tunnel-num min 50 max 55
    
    R2#show run int Lo10 | sec int
    interface Loopback10
     ip address 2.2.2.2 255.255.255.255
    
    R2#show run all | sec ^mpls ip__
    mpls ip
    
    R2#show run | sec ^vrf
    vrf definition Gold
     rd 65100:1
     !
     address-family ipv4
      route-target export 65100:1
      route-target import 65100:2
     exit-address-family
    
    R2#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R2#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R1 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.1.1 255.255.255.252
    
    R2#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R3 **
     ip address 10.1.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R2#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0002.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    router bgp 65100
     bgp router-id 2.2.2.2
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.1.0 mask 255.255.255.252
      neighbor 10.0.1.2 remote-as 65001
      neighbor 10.0.1.2 activate
     exit-address-family
    
R6 (PE)
    R6#show run | sec ^mpls
    mpls label range 600 699
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel primary onehop
    mpls traffic-eng auto-tunnel primary config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel primary config mpls ip
    mpls traffic-eng auto-tunnel primary tunnel-num min 50 max 55
    
    R6#show run int Lo10 | sec int
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run all | sec ^mpls ip__
    mpls ip
    
    R6#show run | sec ^vrf
    vrf definition Gold
     rd 65100:2
     !
     address-family ipv4
      route-target export 65100:2
      route-target import 65100:1
     exit-address-family
     
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.2.1 255.255.255.252
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.4.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R6#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0006.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    router bgp 65100
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.2.0 mask 255.255.255.252
      neighbor 10.0.2.2 remote-as 65002
      neighbor 10.0.2.2 activate
     exit-address-family
    
R3
    R3#show run | sec ^mpls
    mpls label range 300 399
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel primary onehop
    mpls traffic-eng auto-tunnel primary config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel primary config mpls ip
    mpls traffic-eng auto-tunnel primary tunnel-num min 50 max 55
    
    R3#show run int Lo10 | sec int
    interface Loopback10
     ip address 3.3.3.3 255.255.255.255
    
    R3#show run all | sec ^mpls ip__
    mpls ip
    
    R3#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to PE R2 **
     ip address 10.1.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R3#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R4 **
     ip address 10.2.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R3#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0003.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    
R4
    R4#show run | sec ^mpls
    mpls label range 400 499
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel primary onehop
    mpls traffic-eng auto-tunnel primary config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel primary config mpls ip
    mpls traffic-eng auto-tunnel primary tunnel-num min 50 max 55
    
    R4#show run int Lo10 | sec int
    interface Loopback10
     ip address 4.4.4.4 255.255.255.255
    
    R4#show run all | sec ^mpls ip__  
    mpls ip
    
    R4#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R3 **
     ip address 10.2.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.3.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/2 | sec int
    interface GigabitEthernet0/2
     description ** to BGP RR R8 **
     ip address 10.5.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     isis circuit-type level-2-only
     isis network point-to-point
    
    R4#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0004.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    
R5
    R5#show run | sec ^mpls
    mpls label range 500 599
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel primary onehop
    mpls traffic-eng auto-tunnel primary config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel primary config mpls ip
    mpls traffic-eng auto-tunnel primary tunnel-num min 50 max 55
    
    R5#show run int Lo10 | sec int
    interface Loopback10
     ip address 5.5.5.5 255.255.255.255
    
    R5#show run all | sec ^mpls ip__
    mpls ip
    
    R5#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to PE R6 **
     ip address 10.4.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R5#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R4 **
     ip address 10.3.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R5#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0005.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    
R8 (BGP RR)
    R8#show run int Lo10 | sec int
    interface Loopback10
     ip address 8.8.8.8 255.255.255.255
    
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R4 **
     ip address 10.5.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     isis circuit-type level-2-only
     isis network point-to-point
    
    R8#show run | sec ^router
    router isis
     net 49.0010.0000.0000.0008.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    router bgp 65100
     bgp router-id 8.8.8.8
     bgp log-neighbor-changes
     neighbor 2.2.2.2 remote-as 65100
     neighbor 2.2.2.2 update-source Loopback10
     neighbor 6.6.6.6 remote-as 65100
     neighbor 6.6.6.6 update-source Loopback10
     !
     address-family vpnv4
      neighbor 2.2.2.2 activate
      neighbor 2.2.2.2 send-community extended
      neighbor 2.2.2.2 route-reflector-client
      neighbor 6.6.6.6 activate
      neighbor 6.6.6.6 send-community extended
      neighbor 6.6.6.6 route-reflector-client
     exit-address-family
    
R1 (CE)
    R1#show run | sec ^vrf
    vrf definition Gold
     rd 1:1
     !
     address-family ipv4
     exit-address-family
    
    R1#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R1#show run int Gi0/0.1 | sec int
    interface GigabitEthernet0/0.1
     description ** to Host1 in VRF Gold (VLAN 1) **
     encapsulation dot1Q 1 native
     vrf forwarding Gold
     ip address 192.168.1.2 255.255.255.0
    
    R1#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R1#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R2 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.1.2 255.255.255.252
    
    R1#show run | sec ^router
    router bgp 65001
     bgp router-id 1.1.1.1
     bgp log-neighbor-changes
     !
     address-family ipv4 vrf Gold
      network 192.168.1.0
      neighbor 10.0.1.1 remote-as 65100
      neighbor 10.0.1.1 activate
     exit-address-family
    
R7 (CE)
    R7#show run | sec ^vrf
    vrf definition Gold
     rd 1:1
     !
     address-family ipv4
     exit-address-family
    
    R7#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/0.1 | sec int
    interface GigabitEthernet0/0.1
     description ** to Host2 in VRF Gold (VLAN 1) **
     encapsulation dot1Q 1 native
     vrf forwarding Gold
     ip address 192.168.2.2 255.255.255.0
    
    R7#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R6 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R6 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.2.2 255.255.255.252
    
    R7#show run | sec ^router
    router bgp 65002
     bgp router-id 7.7.7.7
     bgp log-neighbor-changes
     !
     address-family ipv4 vrf Gold
      network 192.168.2.0
      neighbor 10.0.2.1 remote-as 65100
      neighbor 10.0.2.1 activate
     exit-address-family
    
Host1
    Host1#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R1 **
     ip address 192.168.1.1 255.255.255.0
     duplex auto
     speed auto
     media-type rj45
    
    Host1#show run | sec ^ip route
    ip route 0.0.0.0 0.0.0.0 192.168.1.2
    
Host1#ping 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/49/50 ms         « Host1 (Site 1) can reach Host2 (Site 2)





Host1#trace 192.168.2.1 probe 1
Type escape sequence to abort.
Tracing the route to 192.168.2.1
VRF info: (vrf in name/id, vrf out name/id)
  1 192.168.1.2 2 msec
  2 10.0.1.1 23 msec
  3 10.1.0.2 [MPLS: Labels 303/606 Exp 0] 48 msec                   « MPLS label stack is used
  4 10.2.0.2 [MPLS: Labels 403/606 Exp 0] 49 msec
  5 10.3.0.2 [MPLS: Labels 503/606 Exp 0] 49 msec
  6 10.0.2.1 [MPLS: Label 606 Exp 0] 28 msec                        « Site 2 VPN Service Label assigned by PE R6
  7 10.0.2.2 48 msec
  8 192.168.2.1 50 msec






R2#show mpls ldp neighbor 
    Peer LDP Ident: 3.3.3.3:0; Local LDP Ident 2.2.2.2:0
        TCP connection: 3.3.3.3.21411 - 2.2.2.2.646
        State: Oper; Msgs sent/rcvd: 52/52; Downstream
        Up time: 00:35:47
        LDP discovery sources:
          Targeted Hello 2.2.2.2 -> 3.3.3.3, active, passive        « Targeted-LDP session between PE R2 and R3
        Addresses bound to peer LDP Ident:
          10.1.0.2        10.2.0.1        3.3.3.3 





R2#show mpls traffic-eng tunnels brief
Signalling Summary:
    LSP Tunnels Process:            running
    Passive LSP Listener:           running
    RSVP Process:                   running
    Forwarding:                     enabled
    auto-tunnel:
        backup Disabled (0 ), id-range:65436-65535
        onehop Enabled  (1 ), id-range:50-55                        « One primary autotunnel created on PE R2
        mesh   Disabled (0 ), id-range:64336-65335

    Periodic reoptimization:        every 3600 seconds, next in 1365 seconds
    Periodic FRR Promotion:         Not Running
    Periodic auto-tunnel:         
        primary establish scan:     every 10 seconds, next in 4 seconds
        primary rm active scan:     disabled
    Periodic auto-bw collection:    every 300 seconds, next in 165 seconds
TUNNEL NAME                      DESTINATION      UP IF      DOWN IF    STATE/PROT
R2_t50                           3.3.3.3          -         Gi0/1     up/up        « TE tunnels are unidirectional, and created in both directions
R3_t51                           2.2.2.2          Gi0/1      -          up/up     
Displayed 1 (of 1) heads, 0 (of 0) midpoints, 1 (of 1) tails






R2#show mpls forwarding-table 
Local      Outgoing   Prefix           Bytes Label   Outgoing   Next Hop    
Label      Label      or Tunnel Id     Switched      interface              
200   [T]  Pop Label  3.3.3.3/32       0             Tu50       point2point         « Traffic is forwarding via autotunnel primary
201   [T]  301        4.4.4.4/32       0             Tu50       point2point 
202   [T]  302        5.5.5.5/32       0             Tu50       point2point 
203   [T]  303        6.6.6.6/32       0             Tu50       point2point 
204   [T]  304        8.8.8.8/32       0             Tu50       point2point 
205        No Label   10.0.1.0/30[V]   0             aggregate/Gold 
206        No Label   192.168.1.0/24[V]   \
                                       2988          Gi0/0.10   10.0.1.2    

[T]     Forwarding through a LSP tunnel.
        View additional labelling info with the 'detail' option





R2#show ip int br
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0         unassigned      YES NVRAM  up                    up      
GigabitEthernet0/0.10      10.0.1.1        YES NVRAM  up                    up      
GigabitEthernet0/1         10.1.0.1        YES NVRAM  up                    up      
GigabitEthernet0/2         unassigned      YES NVRAM  administratively down down    
GigabitEthernet0/3         unassigned      YES NVRAM  administratively down down    
Loopback10                 2.2.2.2         YES NVRAM  up                    up      
Tunnel50                   2.2.2.2         YES TFTP   up                    up      « Dynamically created autotunnel primary






R3#show ip int br
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0         10.1.0.2        YES NVRAM  up                    up      
GigabitEthernet0/1         10.2.0.1        YES NVRAM  up                    up      
GigabitEthernet0/2         unassigned      YES NVRAM  administratively down down    
GigabitEthernet0/3         unassigned      YES NVRAM  administratively down down    
Loopback10                 3.3.3.3         YES NVRAM  up                    up      
Tunnel50                   3.3.3.3         YES TFTP   up                    up      
Tunnel51                   3.3.3.3         YES TFTP   up                    up

As visible in the above outputs, Host1 can reach Host2 through a series of autotunnels creating an LSP between the two PE routers. Note that the dynamically created primary autotunnels have Fast Reroute (FRR) enabled by default. In order to benefit from the FRR feature, the autotunnel backup can be configured (which is described in the next section). The following output shows the dynamically created configuration of a primary autotunnel.

R2#show derived-config | sec interface Tunnel50
interface Tunnel50
 ip unnumbered Loopback10
 no logging event link-status
 mpls ip                                                                « LDP enabled
 tunnel mode mpls traffic-eng
 tunnel destination 3.3.3.3
 tunnel mpls traffic-eng autoroute announce
 tunnel mpls traffic-eng path-option 1 explicit name __dynamic_tunnel50
 tunnel mpls traffic-eng fast-reroute                                   « FRR desired, would need additional configuration to enable backup tunnel
 no routing dynamic

In case of a link failure between two LSRs the autotunnel can be dynamically removed. This feature is enabled by adding the example global configuration command mpls traffic-eng auto-tunnel primary timers removal rerouted 60 on R2. As a result, the primary autotunnel state is scanned and verified every 60 seconds on R2, as shown in the following output.

R2#show mpls traffic-eng tunnels brief
Signalling Summary:
    LSP Tunnels Process:            running
    Passive LSP Listener:           running
    RSVP Process:                   running
    Forwarding:                     enabled
    auto-tunnel:
        backup Disabled (0 ), id-range:65436-65535
        onehop Enabled  (1 ), id-range:50-55
        mesh   Disabled (0 ), id-range:64336-65335

    Periodic reoptimization:        every 3600 seconds, next in 172 seconds
    Periodic FRR Promotion:         Not Running
    Periodic auto-tunnel:         
        primary establish scan:     every 10 seconds, next in 1 seconds
        primary rm active scan:     every 60 seconds, next in 58 seconds
    Periodic auto-bw collection:    every 300 seconds, next in 172 seconds
TUNNEL NAME                      DESTINATION      UP IF      DOWN IF    STATE/PROT
R2_t50                           3.3.3.3          -         Gi0/1     up/up     
R3_t51                           2.2.2.2          Gi0/1      -          up/up     
Displayed 1 (of 1) heads, 0 (of 0) midpoints, 1 (of 1) tails

Configuring MPLS TE autotunnel backup

In the following example scenario the link between R3 - R4 is protected with the autotunnel backup feature. This means, the feature is enabled in global configuration mode, instructing the routers to dynamically find and create nhop-only (link protection) fast reroute (FRR) backup tunnels. Since there is an alternative path through R9, the router R3 and R4 establish a backup (bypass) tunnel through the alternative path.

Also, on the protected link BFD is configured for improved failure detection times. When the link fails, traffic is immediately switched to the autotunnel backup path. Note that an additional MPLS label is added for traffic transmitted through the FRR backup tunnel.

MPLS TE autotunnel backup configuration with nhop-only and IGP OSPF

Configuration:

R2 (PE)
    R2#show run | sec ^mpls
    mpls label range 200 299
    mpls traffic-eng tunnels
    
    R2#show run | sec ^vrf
    vrf definition Gold
     rd 65100:1
     !
     address-family ipv4
      route-target export 65100:1
      route-target import 65100:2
     exit-address-family
    
    R2#show run int Lo10 | sec int
    interface Loopback10
     ip address 2.2.2.2 255.255.255.255
    
    R2#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R2#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R1 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.1.1 255.255.255.252
    
    R2#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R3 **
     ip address 10.1.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R2#show run int Tu10 | sec int
    interface Tunnel10
     description ** MPLS TE tunnel to PE R6 **
     ip unnumbered Loopback10
     tunnel mode mpls traffic-eng
     tunnel destination 6.6.6.6
     tunnel mpls traffic-eng autoroute announce
     tunnel mpls traffic-eng priority 1 1
     tunnel mpls traffic-eng bandwidth 50
     tunnel mpls traffic-eng path-option 10 explicit name EXAMPLE-PATH
     tunnel mpls traffic-eng fast-reroute
     no routing dynamic
    
    R2#show run | sec ^ip exp
    ip explicit-path name EXAMPLE-PATH enable
     next-address 3.3.3.3
     next-address 4.4.4.4
     next-address 5.5.5.5
     next-address 6.6.6.6
    
    R2#show run | sec ^router
    router ospf 10
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng area 0
     router-id 2.2.2.2
     network 2.2.2.2 0.0.0.0 area 0
     network 10.1.0.0 0.0.0.3 area 0
    router bgp 65100
     bgp router-id 2.2.2.2
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.1.0 mask 255.255.255.252
      neighbor 10.0.1.2 remote-as 65001
      neighbor 10.0.1.2 activate
     exit-address-family
    
R6 (PE)
    R6#show run | sec ^mpls
    mpls label range 600 699
    mpls traffic-eng tunnels
    
    R6#show run | sec ^vrf  
    vrf definition Gold
     rd 65100:2
     !
     address-family ipv4
      route-target export 65100:2
      route-target import 65100:1
     exit-address-family
    
    R6#show run int Lo10 | sec int 
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.2.1 255.255.255.252
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.4.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R6#show run int Tu10 | sec int 
    interface Tunnel10
     description ** MPLS TE tunnel to PE R2 **
     ip unnumbered Loopback10
     tunnel mode mpls traffic-eng
     tunnel destination 2.2.2.2
     tunnel mpls traffic-eng autoroute announce
     tunnel mpls traffic-eng priority 1 1
     tunnel mpls traffic-eng bandwidth 50
     tunnel mpls traffic-eng path-option 10 explicit name EXAMPLE-PATH
     tunnel mpls traffic-eng fast-reroute
     no routing dynamic
    
    R6#show run | sec ^ip exp
    ip explicit-path name EXAMPLE-PATH enable
     next-address 5.5.5.5
     next-address 4.4.4.4
     next-address 3.3.3.3
     next-address 2.2.2.2
    
    R6#show run | sec ^router
    router ospf 10
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng area 0
     router-id 6.6.6.6
     network 6.6.6.6 0.0.0.0 area 0
     network 10.4.0.0 0.0.0.3 area 0
    router bgp 65100
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.2.0 mask 255.255.255.252
      neighbor 10.0.2.2 remote-as 65002
      neighbor 10.0.2.2 activate
     exit-address-family
    
R3
    R3#show run | sec ^mpls
    mpls label range 300 399
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel backup nhop-only
    mpls traffic-eng auto-tunnel backup config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel backup timers removal unused 60 30
    mpls traffic-eng auto-tunnel backup tunnel-num min 50 max 55
    
    R3#show run int Lo10 | sec int
    interface Loopback10
     ip address 3.3.3.3 255.255.255.255
    
    R3#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to PE R2 **
     ip address 10.1.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R3#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R4 **
     ip address 10.2.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     bfd interval 100 min_rx 100 multiplier 3
     ip rsvp bandwidth 100 50
    
    R3#show run int Gi0/2 | sec int
    interface GigabitEthernet0/2
     description ** to R9 - autotunnel backup path **
     ip address 10.6.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R3#show run | sec ^router
    router ospf 10
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng area 0
     router-id 3.3.3.3
     network 3.3.3.3 0.0.0.0 area 0
     network 10.1.0.0 0.0.0.3 area 0
     network 10.2.0.0 0.0.0.3 area 0
     network 10.6.0.0 0.0.0.3 area 0
    
R4
    R4#show run | sec ^mpls
    mpls label range 400 499
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel backup nhop-only
    mpls traffic-eng auto-tunnel backup config unnumbered-interface Loopback10
    mpls traffic-eng auto-tunnel backup timers removal unused 60 30
    mpls traffic-eng auto-tunnel backup tunnel-num min 50 max 55
    
    R4#show run int Lo10 | sec int
    interface Loopback10
     ip address 4.4.4.4 255.255.255.255
    
    R4#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R3 **
     ip address 10.2.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     bfd interval 100 min_rx 100 multiplier 3
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.3.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/2 | sec int
    interface GigabitEthernet0/2
     description ** to BGP RR R8 **
     ip address 10.5.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R4#show run int Gi0/3 | sec int
    interface GigabitEthernet0/3
     description ** to R9 - autotunnel backup path **
     ip address 10.7.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R4#show run | sec ^router
    router ospf 10
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng area 0
     router-id 4.4.4.4
     network 4.4.4.4 0.0.0.0 area 0
     network 10.2.0.0 0.0.0.3 area 0
     network 10.3.0.0 0.0.0.3 area 0
     network 10.5.0.0 0.0.0.3 area 0
     network 10.7.0.0 0.0.0.3 area 0
    
R8 (BGP RR)
    R8#show run int Lo10 | sec int
    interface Loopback10
     ip address 8.8.8.8 255.255.255.255
    
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R4 **
     ip address 10.5.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run | sec ^router
    router ospf 10
     router-id 8.8.8.8
     network 8.8.8.8 0.0.0.0 area 0
     network 10.5.0.0 0.0.0.3 area 0
    router bgp 65100
     bgp router-id 8.8.8.8
     bgp log-neighbor-changes
     neighbor 2.2.2.2 remote-as 65100
     neighbor 2.2.2.2 update-source Loopback10
     neighbor 6.6.6.6 remote-as 65100
     neighbor 6.6.6.6 update-source Loopback10
     !
     address-family vpnv4
      neighbor 2.2.2.2 activate
      neighbor 2.2.2.2 send-community extended
      neighbor 2.2.2.2 route-reflector-client
      neighbor 6.6.6.6 activate
      neighbor 6.6.6.6 send-community extended
      neighbor 6.6.6.6 route-reflector-client
     exit-address-family
    
R9
    R9#show run | sec ^mpls
    mpls label range 900 999
    mpls traffic-eng tunnels
    
    R9#show run int Lo10 | sec int
    interface Loopback10
     ip address 9.9.9.9 255.255.255.255
    
    R9#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R3 **
     ip address 10.6.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R9#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R4 **
     ip address 10.7.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     ip rsvp bandwidth 100 50
    
    R9#show run | sec ^router
    router ospf 10
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng area 0
     router-id 9.9.9.9
     network 9.9.9.9 0.0.0.0 area 0
     network 10.6.0.0 0.0.0.3 area 0
     network 10.7.0.0 0.0.0.3 area 0
    
R3#show ip rsvp fast-reroute
Primary                   Protect BW         Backup       
Tunnel                    I/F     BPS:Type   Tunnel:Label  State  Level   Type  
------                    ------- --------   ------------- ------ -----   ------
** MPLS TE tunnel to PE R Gi0/0   50K:G      None          None   None   
** MPLS TE tunnel to PE R Gi0/1   50K:G      Tu52:403      Ready  any-unl Nhop         « Autotunnel backup is ready for use





R3#show mpls traffic-eng tunnels backup
R3_t50
  LSP Head, Tunnel50, Admin: up, Oper: down
  Src 3.3.3.3, Dest 2.2.2.2, Instance 0
  Fast Reroute Backup Provided: 
    Protected i/fs: Gi0/0
    Protected lsps: 0 Active lsps: 0
    Backup BW: any pool unlimited; inuse: 0 kbps 
R3_t52
  LSP Head, Tunnel52, Admin: up, Oper: up           « Backup tunnel is operational
  Src 3.3.3.3, Dest 4.4.4.4, Instance 1             « Backup tunnel protects LSP between R3 and R4
  Fast Reroute Backup Provided: 
    Protected i/fs: Gi0/1
    Protected lsps: 1 Active lsps: 0                « One LSP protected
    Backup BW: any pool unlimited; inuse: 50 kbps




R3#show bfd summary client

Client              Session          Up          Down
FRR                       1           1             0      « Fast Reroute is a client of BFD
CEF                       1           1             0

Total                     1           1             0




Host1#trace 192.168.2.1 probe 1
Type escape sequence to abort.
Tracing the route to 192.168.2.1
VRF info: (vrf in name/id, vrf out name/id)
  1 192.168.1.2 2 msec
  2 10.0.1.1 24 msec
  3 10.1.0.2 [MPLS: Labels 304/606 Exp 0] 70 msec          « LSP before link failure
  4 10.2.0.2 [MPLS: Labels 403/606 Exp 0] 71 msec
  5 10.3.0.2 [MPLS: Labels 503/606 Exp 0] 72 msec
  6 10.0.2.1 [MPLS: Label 606 Exp 0] 49 msec
  7 10.0.2.2 70 msec
  8 192.168.2.1 72 msec
  




Host1#ping 192.168.2.1 re 100
Type escape sequence to abort.
Sending 100, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 99 percent (99/100), round-trip min/avg/max = 68/79/96 ms       « Link failure causes single packet loss





Host1#trace 192.168.2.1 probe 1
Type escape sequence to abort.
Tracing the route to 192.168.2.1
VRF info: (vrf in name/id, vrf out name/id)
  1 192.168.1.2 2 msec
  2 10.0.1.1 24 msec
  3 10.1.0.2 [MPLS: Labels 304/606 Exp 0] 92 msec
  4 10.6.0.2 [MPLS: Labels 900/403/606 Exp 0] 94 msec      « Additional MPLS label added for traffic in backup tunnel
  5 10.7.0.1 [MPLS: Labels 403/606 Exp 0] 92 msec
  6 10.3.0.2 [MPLS: Labels 503/606 Exp 0] 92 msec
  7 10.0.2.1 [MPLS: Label 606 Exp 0] 71 msec
  8 10.0.2.2 92 msec
  9 192.168.2.1 91 msec

Configuring MPLS TE autotunnel mesh

In the following example scenario the two PE routers establish an LSP across the Service Provider network using an MPLS TE tunnel template. This means, a tunnel interface template is configured (similar to DVTI), and the template configuration is cloned to any number of automatically created MPLS TE tunnels.

The tunnel peers are configured with either an access-list (ACL) or using a mesh group. Note the routing protocol IS-IS only supports ACLs with autotunnel mesh. Therefore, in the following example an ACL is used on each PE router to identify any other PE routers within the autotunnel mesh network. The PEs allowed by the ACL will automatically establish an MPLS TE tunnel based on the template, and create an LSP.

MPLS TE autotunnel mesh configuration on each PE router with an access-list to identify tunnel destination

Configuration:

R2 (PE)
    R2#show run | sec ^mpls
    mpls label range 200 299
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel mesh
    mpls traffic-eng auto-tunnel mesh tunnel-num min 50 max 55
    
    R2#show run int Auto-Template10 | sec int
    interface Auto-Template10
     ip unnumbered Loopback10
     tunnel mode mpls traffic-eng
     tunnel destination access-list 10
     tunnel mpls traffic-eng autoroute announce
     tunnel mpls traffic-eng path-option 1 dynamic
     no routing dynamic
    
    R2#show run | sec ^access-list
    access-list 10 permit 6.6.6.6
    
    R2#show run int Lo10 | sec int
    interface Loopback10
     ip address 2.2.2.2 255.255.255.255
    
    R2#show run | sec ^vrf
    vrf definition Gold
     rd 65100:1
     !
     address-family ipv4
      route-target export 65100:1
      route-target import 65100:2
     exit-address-family
    
    R2#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R2#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R1 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.1.1 255.255.255.252
    
    R2#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R3 **
     ip address 10.1.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R2#show run | sec ^router     
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0002.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    router bgp 65100
     bgp router-id 2.2.2.2
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.1.0 mask 255.255.255.252
      neighbor 10.0.1.2 remote-as 65001
      neighbor 10.0.1.2 activate
     exit-address-family 
    
R6 (PE)
    R6#show run | sec ^mpls
    mpls label range 600 699
    mpls traffic-eng tunnels
    mpls traffic-eng auto-tunnel mesh
    mpls traffic-eng auto-tunnel mesh tunnel-num min 50 max 55
    
    R6#show run int Auto-Template10 | sec int
    interface Auto-Template10
     ip unnumbered Loopback10
     tunnel mode mpls traffic-eng
     tunnel destination access-list 10
     tunnel mpls traffic-eng autoroute announce
     tunnel mpls traffic-eng path-option 1 dynamic
     no routing dynamic
    
    R6#show run | sec ^access-list
    access-list 10 permit 2.2.2.2
    
    R6#show run int Lo10 | sec int
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run | sec ^vrf
    vrf definition Gold
     rd 65100:2
     !
     address-family ipv4
      route-target export 65100:2
      route-target import 65100:1
     exit-address-family
    
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF Gold **
     encapsulation dot1Q 10
     vrf forwarding Gold
     ip address 10.0.2.1 255.255.255.252
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.4.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R6#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0006.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    router bgp 65100
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 8.8.8.8 remote-as 65100
     neighbor 8.8.8.8 update-source Loopback10
     !
     address-family vpnv4
      neighbor 8.8.8.8 activate
      neighbor 8.8.8.8 send-community extended
     exit-address-family
     !
     address-family ipv4 vrf Gold
      network 10.0.2.0 mask 255.255.255.252
      neighbor 10.0.2.2 remote-as 65002
      neighbor 10.0.2.2 activate
     exit-address-family
    
R3
    R3#show run | sec ^mpls
    mpls label range 300 399
    mpls traffic-eng tunnels
    
    R3#show run int Lo10 | sec int
    interface Loopback10
     ip address 3.3.3.3 255.255.255.255
    
    R3#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to PE R2 **
     ip address 10.1.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R3#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R4 **
     ip address 10.2.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R3#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0003.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    
R4
    R4#show run | sec ^mpls
    mpls label range 400 499
    mpls traffic-eng tunnels
    
    R4#show run int Lo10 | sec int
    interface Loopback10
     ip address 4.4.4.4 255.255.255.255
    
    R4#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R3 **
     ip address 10.2.0.2 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R5 **
     ip address 10.3.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     mpls traffic-eng tunnels
     isis circuit-type level-2-only
     isis network point-to-point 
     ip rsvp bandwidth 100 50
    
    R4#show run int Gi0/2 | sec int
    interface GigabitEthernet0/2
     description ** to BGP RR R8 **
     ip address 10.5.0.1 255.255.255.252
     ip router isis 
     duplex auto
     speed auto
     media-type rj45
     isis circuit-type level-2-only
     isis network point-to-point
    
    R4#show run | sec ^router
    router isis
     mpls traffic-eng router-id Loopback10
     mpls traffic-eng level-2
     net 49.0010.0000.0000.0004.00
     is-type level-2-only
     advertise passive-only
     metric-style wide
     log-adjacency-changes
     passive-interface Loopback10
    
R2#show mpls traffic-eng auto-tunnel mesh 

Auto-Template10:

 Using access-list 10 to clone the following tunnel interfaces:

  Destination         Interface   
  -----------         ---------   

  6.6.6.6             Tunnel50             « Tunnel automatically created

Mesh tunnel interface numbers: min 50 max 55






R2#show mpls traffic-eng tunnels brief    
Signalling Summary:
    LSP Tunnels Process:            running
    Passive LSP Listener:           running
    RSVP Process:                   running
    Forwarding:                     enabled
    auto-tunnel:
        backup Disabled (0 ), id-range:65436-65535
        onehop Disabled (0 ), id-range:65336-65435
        mesh   Enabled  (1 ), id-range:50-55            « Autotunnel mesh is enabled

    Periodic reoptimization:        every 3600 seconds, next in 3428 seconds
    Periodic FRR Promotion:         Not Running
    Periodic auto-bw collection:    every 300 seconds, next in 128 seconds
TUNNEL NAME                      DESTINATION      UP IF      DOWN IF    STATE/PROT
R2_t50                           6.6.6.6          -         Gi0/1     up/up              « This is the tunnel head
R6_t50                           2.2.2.2          Gi0/1      -          up/up            « This is the tunnel tail
Displayed 1 (of 1) heads, 0 (of 0) midpoints, 1 (of 1) tails





Host1#trace 192.168.2.1 probe 1
Type escape sequence to abort.
Tracing the route to 192.168.2.1
VRF info: (vrf in name/id, vrf out name/id)
  1 192.168.1.2 2 msec
  2 10.0.1.1 23 msec
  3 10.1.0.2 [MPLS: Labels 300/606 Exp 0] 48 msec              « MPLS label switching is used
  4 10.2.0.2 [MPLS: Labels 401/606 Exp 0] 50 msec
  5 10.3.0.2 [MPLS: Labels 501/606 Exp 0] 48 msec
  6 10.0.2.1 [MPLS: Label 606 Exp 0] 26 msec
  7 10.0.2.2 49 msec
  8 192.168.2.1 50 msec

In the following outputs the same network is recreated using OSPF as the IGP, instead of IS-IS. The displayed configuration is taken from the PE router R2 and R6, and shows the MPLS TE autotunnel mesh-group being used to identify each PE router in the network.

R2#show run | sec ^router ospf
router ospf 10
 mpls traffic-eng router-id Loopback10
 mpls traffic-eng area 0
 mpls traffic-eng mesh-group 10 Loopback10 area 0           « The mesh-group ID 10 is used between the PE routers
 router-id 2.2.2.2
 network 2.2.2.2 0.0.0.0 area 0
 network 10.1.0.0 0.0.0.3 area 0


-----------------------------------------------------


R6#show run | sec ^router ospf
router ospf 10
 mpls traffic-eng router-id Loopback10
 mpls traffic-eng area 0
 mpls traffic-eng mesh-group 10 Loopback10 area 0
 router-id 6.6.6.6
 network 6.6.6.6 0.0.0.0 area 0
 network 10.4.0.0 0.0.0.3 area 0

The following outputs are taken from the PE router R2 showing the mesh-group ID 10 advertised by the OSPF routing protocol. This feature is available only with OSPF, and is not available with IS-IS.

R2#show mpls traffic-eng topology area 0 igp-id ospf 6.6.6.6 brief

IGP Id: 6.6.6.6, MPLS TE Id:6.6.6.6 Router Node  (ospf 10  area 0)
Area mg-id's:
: mg-id 10    6.6.6.6 :                                « Mesh-group ID 10
      link[0]: Point-to-Point, Nbr IGP Id: 5.5.5.5, nbr_node_id:10, gen:14
          frag_id 2, Intf Address:10.4.0.1, Nbr Intf Address:10.4.0.2
          TE metric:1, IGP metric:1, attribute flags:0x0
          SRLGs: None





R2#show ip ospf database opaque-area adv-router 6.6.6.6 | beg Number of Links : 1     
    Number of Links : 1

  LS age: 655
  Options: (No TOS-capability, DC)
  LS Type: Opaque Area Link
  Link State ID: 4.0.0.0
  Opaque Type: 4 (Router Information)
  Opaque ID: 0
  Advertising Router: 6.6.6.6
  LS Seq Number: 80000002
  Checksum: 0xD893
  Length: 40

    TLV Type: Router Information
    Length: 4
    Capabilities:
      Graceful Restart Helper
      Stub Router Support
      Traffic Engineering Support

    TLV Type: Mesh-group (IPv4)                        « Mesh-group information carried in OSPF Opaque LSA
    Length: 8
    Encoding: Cisco
      Mesh-group Number: 10
        Tail-end IP: 6.6.6.6

The details shown in the router outputs taken from the OSPF database are displayed in the following packet capture. As visible, OSPF uses the Opaque LSA Type 10 to distribute information regarding the MPLS Traffic Engineering Autotunnel Mesh Group. With this integrated feature, PE routers can use the mesh-group ID to indentify each other and dynamically establish MPLS TE tunnels.

OSPF Opaque LSA Type 10 with Mesh-Group TLV