MPLS 6VPE Introduction and IPv6 VPN Configuration

« 2023 Feb 17 »

What is MPLS 6VPE?

MPLS 6VPE enables connecting IPv6-only sites over an IPv4 MPLS-enabled core network. MPLS 6VPE leverages the existing infrastructure to tunnel IPv6 traffic with label switching. As a result, Service Providers can use their IPv4 MPLS core networks to provide IPv6 services.

6VPE offers MPLS L3VPN services such as multitenancy through VPN/VRF tables in order to enable independent IPv6 routing domains. Thus, MPLS 6VPE can transport overlapping IPv6 addresses virtually separated for each subscriber while using the same shared infrastructure. The following image provides a summary of MPLS 6VPE.

MPLS 6VPE network overview explaining L3VPN to connect IPv6 sites over an IPv4 Service Provider network by using dual stack IPv4 - IPv6 PE routers

The technology is made possible with the MPLS label stack that ensures connectivity for each virtual network (IPv4 or IPv6) by assigning a unique VPN Service Label. The VPN Service Label is assigned by the PE routers. The following capture shows a BGP VPNv6 Update sent from a Route Reflector to a PE router, and carrying an IPv6 prefix together with the VPN Service Label 609.

BGP VPNv6 IPv6 Update for MPLS L3VPN 6VPE

How to configure MPLS 6VPE?

The following are important elements that make an MPLS 6VPE network function.

  • MPLS core transport network is configured with IPv4 IGP OSPF or IS-IS. Routers in the provider core (not PE and not RR) have only IPv4 enabled, and will forward IPv6 packets with label switching only.
  • Between PE and CE the access network is configured with IPv6. The chosen PE - CE routing protocol such as eBGP, EIGRP, OSPF needs to be configured in IPv6 over a VRF.
  • On the PE routers the MP-BGP adjacencies are configured in the address-family IPv6 towards the CE, and VPNv6 towards the BGP Route Reflector. The PE routers are dual stack IPv4 and IPv6. On the CE-facing VRF-aware sub-interface the PE router has an IPv6 address. On the MPLS core-facing interface the PE router has an IPv4 address.
MPLS label stack tunneling traffic towards IPv6 remote location

Option 1) Configuring eBGP IPv6 between PE - CE

In the following example scenario, Site 1 and Site 2 are configured with IPv6 and connected through the VRF called "VRF-BLUE" using the IPv4 MPLS Layer-3 VPN (L3VPN) Service Provider network. This means a virtually unique routing table is created within VRF-BLUE, and the site specific IPv6 prefixes are transported in that VRF. The PE - CE routing protocol is eBGP, and between the PE - RR there is a BGP VPNv6 neighborship configured.

Route Target import/export rules configured on the PE routers ensure that the IPv6 prefixes are received. The PE routers are dual stack IPv4/IPv6. The command ipv6 unicast-routing is issued in global configuration mode on each router that runs BGP IPv6 or VPNv6.

Each label switch router (LSR) has the command mpls ip added in global configuration mode, and the MPLS label range is also specified to help understand the traffic flow and illustrate the technology. This means, R1 assigns labels in the range 100 - 199, R2 uses 200 - 299, etc.

Configuration of MPLS 6VPE with BGP VPNv6 between PE and Route Reflector and advertising IPv6 routes for a single VRF

Configuration:

R1
    R1#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to PE R5 **
     ip address 10.3.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R1#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R2 **
     ip address 10.1.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R1#show run int Lo10 | sec int
    interface Loopback10
     ip address 1.1.1.1 255.255.255.255
    
    R1#show run | sec ^router
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 1.1.1.1
     network 1.1.1.1 0.0.0.0 area 0
     network 10.1.0.0 0.0.0.3 area 0
     network 10.3.0.0 0.0.0.3 area 0
    
    R1#show run | sec ^mpls
    mpls label range 100 199
    
R2
    R2#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R1 **
     ip address 10.1.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls ip
    
    R2#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R3 **
     ip address 10.2.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     mpls ip
    
    R2#show run int Gi0/2 | sec int
    interface GigabitEthernet0/2
     description ** to RR R4 **
     ip address 10.4.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R2#show run int Lo10 | sec int 
    interface Loopback10
     ip address 2.2.2.2 255.255.255.255
    
    R2#show run | sec ^router
    router ospf 10
     router-id 2.2.2.2
     network 2.2.2.2 0.0.0.0 area 0
     network 10.1.0.0 0.0.0.3 area 0
     network 10.2.0.0 0.0.0.3 area 0
     network 10.4.0.0 0.0.0.3 area 0
    
    R2#show run | sec ^mpls
    mpls label range 200 299
    
R4 (RR)
    R4#show run | sec ^ipv6 uni
    ipv6 unicast-routing
    
    R4#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to R2 **
     ip address 10.4.0.2 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R4#show run int Lo10 | sec int 
    interface Loopback10
     ip address 4.4.4.4 255.255.255.255
    
    R4#show run | sec ^router
    router ospf 10
     router-id 4.4.4.4
     network 4.4.4.4 0.0.0.0 area 0
     network 10.4.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 4.4.4.4
     bgp log-neighbor-changes
     neighbor 5.5.5.5 remote-as 65010
     neighbor 5.5.5.5 update-source Loopback10
     neighbor 6.6.6.6 remote-as 65010
     neighbor 6.6.6.6 update-source Loopback10
     !
     address-family ipv4
      neighbor 5.5.5.5 activate
      neighbor 5.5.5.5 send-community extended
      neighbor 5.5.5.5 route-reflector-client
      neighbor 6.6.6.6 activate
      neighbor 6.6.6.6 send-community extended
      neighbor 6.6.6.6 route-reflector-client
     exit-address-family
     !
     address-family vpnv6
      neighbor 5.5.5.5 activate
      neighbor 5.5.5.5 send-community extended
      neighbor 5.5.5.5 route-reflector-client
      neighbor 6.6.6.6 activate
      neighbor 6.6.6.6 send-community extended
      neighbor 6.6.6.6 route-reflector-client
     exit-address-family
    
R5 (PE)
    R5#show run | sec ^ipv6 uni
    ipv6 unicast-routing
    
    R5#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:1::1/64
    
    R5#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.3.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Lo10 | sec int 
    interface Loopback10
     ip address 5.5.5.5 255.255.255.255
    
    R5#show run | sec ^router
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 5.5.5.5
     network 5.5.5.5 0.0.0.0 area 0
     network 10.3.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 5.5.5.5
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      neighbor 2001:DB8:1::2 remote-as 65001
      neighbor 2001:DB8:1::2 activate
     exit-address-family
    
    R5#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:1
     !
     address-family ipv6
      route-target export 65010:1
      route-target import 65010:2
     exit-address-family
    
    R5#show run | sec ^mpls
    mpls label range 500 599
    
R6 (PE)
    R6#show run | sec ^ipv6 uni
    ipv6 unicast-routing
    
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R8 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R8 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:2::1/64
     
    R6#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.5.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Lo10 | sec int
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run | sec ^router
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 6.6.6.6
     network 6.6.6.6 0.0.0.0 area 0
     network 10.5.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      neighbor 2001:DB8:2::2 remote-as 65002
      neighbor 2001:DB8:2::2 activate
     exit-address-family
    
    R6#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:2
     !
     address-family ipv6
      route-target export 65010:2
      route-target import 65010:1
     exit-address-family
     
    R6#show run | sec ^mpls
    mpls label range 600 699
    
R7 (CE)
    R7#show run | sec ^ipv6 uni
    ipv6 unicast-routing
    
    R7#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host1 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:A::2/64
    
    R7#show run int Gi0/1 | sec int      
    interface GigabitEthernet0/1
     description ** to PE R5 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R5 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:1::2/64
    
    R7#show run | sec ^router
    router bgp 65001
     bgp router-id 7.7.7.7
     bgp log-neighbor-changes
     !
     address-family ipv6 vrf VRF-BLUE
      network 2001:DB8:A::/64
      neighbor 2001:DB8:1::1 remote-as 65010
      neighbor 2001:DB8:1::1 activate
     exit-address-family
    
    R7#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
R8 (CE)
    R8#show run | sec ^ipv6 uni
    ipv6 unicast-routing
    
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host2 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:B::2/64
    
    R8#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R6 ** 
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R6 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:2::2/64
    
    R8#show run | sec ^router
    router bgp 65002
     bgp router-id 8.8.8.8
     bgp log-neighbor-changes
     !
     address-family ipv6 vrf VRF-BLUE
      network 2001:DB8:B::/64
      neighbor 2001:DB8:2::1 remote-as 65010
      neighbor 2001:DB8:2::1 activate
     exit-address-family
    
    R8#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
Host1
    Host1#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    Host1#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VLAN 10 **
     encapsulation dot1Q 10
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:A::1/64
    
    Host1#show run | sec ^ipv6 route
    ipv6 route ::/0 GigabitEthernet0/0.10 2001:DB8:A::2
    
Host1#trace 2001:DB8:B::1
Type escape sequence to abort.
Tracing the route to 2001:DB8:B::1

  1 2001:DB8:A::2 1 msec 1 msec 1 msec
  2 2001:DB8:1::1 22 msec 24 msec 23 msec
  3 ::FFFF:10.3.0.2 [MPLS: Labels 103/609 Exp 0] 47 msec 48 msec 49 msec      « VPN Service Label assigned by PE R6
  4 ::FFFF:10.1.0.2 [MPLS: Labels 203/609 Exp 0] 47 msec 48 msec 47 msec
  5 ::FFFF:10.2.0.2 [MPLS: Labels 303/609 Exp 0] 48 msec 48 msec 47 msec
  6 2001:DB8:2::1 [MPLS: Label 609 Exp 0] 27 msec 27 msec 27 msec
  7 2001:DB8:2::2 47 msec 47 msec 48 msec
  8 2001:DB8:B::1 49 msec 49 msec 49 msec
 
 


Host2#trace 2001:DB8:A::1
Type escape sequence to abort.
Tracing the route to 2001:DB8:A::1

  1 2001:DB8:B::2 2 msec 2 msec 2 msec
  2 2001:DB8:2::1 23 msec 24 msec 23 msec
  3 ::FFFF:10.5.0.2 [MPLS: Labels 302/509 Exp 0] 48 msec 48 msec 49 msec
  4 ::FFFF:10.2.0.1 [MPLS: Labels 202/509 Exp 0] 47 msec 47 msec 47 msec
  5 ::FFFF:10.1.0.1 [MPLS: Labels 102/509 Exp 0] 48 msec 48 msec 49 msec
  6 2001:DB8:1::1 [MPLS: Label 509 Exp 0] 26 msec 26 msec 26 msec
  7 2001:DB8:1::2 48 msec 48 msec 48 msec
  8 2001:DB8:A::1 49 msec 50 msec 48 msec




R7#show ip bgp vpnv6 unicast vrf VRF-BLUE summary | beg Ne
Neighbor        V           AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
2001:DB8:1::1   4        65010     108     109        3    0    0 01:35:22        1     « eBGP neigbborship CE R7 and PE R5





R7#show ip bgp vpnv6 unicast vrf VRF-BLUE | begin Network
     Network          Next Hop            Metric LocPrf Weight Path
Route Distinguisher: 1:1 (default for vrf VRF-BLUE)
 *>   2001:DB8:A::/64  ::                       0         32768 i
 *>   2001:DB8:B::/64  2001:DB8:1::1                          0 65010 65002 i           « CE R7 receives Site 2 IPv6 route




R5#show ip bgp vpnv6 unicast all | beg Network         
     Network          Next Hop            Metric LocPrf Weight Path
Route Distinguisher: 65010:1 (default for vrf VRF-BLUE)
 *>   2001:DB8:A::/64  2001:DB8:1::2            0             0 65001 i
 *>i  2001:DB8:B::/64  ::FFFF:6.6.6.6           0    100      0 65002 i
Route Distinguisher: 65010:2
 *>i  2001:DB8:B::/64  ::FFFF:6.6.6.6           0    100      0 65002 i     « PE R5 receives Site 2 IPv6 route
 
 
 
 
R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 3
Paths: (1 available, best #1, no table)
Flag: 0x100
  Not advertised to any peer
  Refresh Epoch 1
  65002
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)        « The RR advertises Site 2 route
      Origin IGP, metric 0, localpref 100, valid, internal, best
      Extended Community: RT:65010:2                 « The Route Target value exported and attached on PE R6
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609                 « VPN Service Label assigned by PE R6
      rx pathid: 0, tx pathid: 0x0

In the above router outputs, the IPv6 address of PE R6 is ::FFFF:6.6.6.6 and it is created by mapping IPv4 onto an IPv6 address. This is done by the PE routers to enable carrying IPv6 prefixes across the IPv4 MPLS core network. This type of address notation is outlined in the RFC 4291 and the following quote provides further details.

An alternative form that is sometimes more convenient when dealing with a mixed environment of IPv4 and IPv6 nodes is x:x:x:x:x:x:d.d.d.d, where the 'x's are the hexadecimal values of the six high-order 16-bit pieces of the address, and the 'd's are the decimal values of the four low-order 8-bit pieces of the address (standard IPv4 representation).

RFC 4291, IP Version 6 Addressing Architecture

Option 2) Configuring EIGRP IPv6 between PE - CE

In the following example topology a L3VPN MPLS 6VPE network is configured and connects two IPv6 sites using a single VRF called "VRF-BLUE". The PE - CE routing protocol is EIGRP IPv6. This means, on the PE routers BGP VPNv6 and EIGRP IPv6 redistribute routes in both directions. IPv6 routes learned through EIGRP in VRF-BLUE are redisributed and advertised as BGP VPNv6 prefixes in the MPLS network.

PE - CE routing protocol EIGRP IPv6 configured with MPLS 6VPE network connecting two IPv6 sites in a single VRF

Configuration:

R5 (PE)
    R5#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:1::1/64
    
    R5#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.3.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Lo10 | sec int
    interface Loopback10
     ip address 5.5.5.5 255.255.255.255
    
    R5#show run | sec ^router
    router eigrp EIGRP-IPv6
     !
     address-family ipv6 unicast vrf VRF-BLUE autonomous-system 10
      !
      topology base
       redistribute bgp 65010 metric 1000 10 255 1 1500
      exit-af-topology
      eigrp router-id 5.5.5.5
     exit-address-family
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 5.5.5.5
     network 5.5.5.5 0.0.0.0 area 0
     network 10.3.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 5.5.5.5
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute eigrp 10
     exit-address-family
    
    R5#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:1
     !
     address-family ipv6
      route-target export 65010:1
      route-target import 65010:2
     exit-address-family
    
    R5#show run | sec ^mpls
    mpls label range 500 599
    
R6 (PE)
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R8 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R8 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:2::1/64
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.5.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Lo10 | sec int
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run | sec ^router
    router eigrp EIGRP-IPv6
     !
     address-family ipv6 unicast vrf VRF-BLUE autonomous-system 10
      !
      topology base
       redistribute bgp 65010 metric 1000 10 255 1 1500
      exit-af-topology
      eigrp router-id 6.6.6.6
     exit-address-family
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 6.6.6.6
     network 6.6.6.6 0.0.0.0 area 0
     network 10.5.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute eigrp 10
     exit-address-family
    
    R6#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:2
     !
     address-family ipv6
      route-target export 65010:2
      route-target import 65010:1
     exit-address-family
    
    R6#show run | sec ^mpls
    mpls label range 600 699
    
R7 (CE)
    R7#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host1 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:A::2/64
    
    R7#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R5 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R5 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:1::2/64
    
    R7#show run | sec ^router
    router eigrp EIGRP-IPv6
     !
     address-family ipv6 unicast vrf VRF-BLUE autonomous-system 10
      !
      topology base
      exit-af-topology
      eigrp router-id 7.7.7.7
     exit-address-family
    
    R7#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
R8 (CE)
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host2 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:B::2/64
    
    R8#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R6 ** 
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R6 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:2::2/64
     
    R8#show run | sec ^router
    router eigrp EIGRP-IPv6
     !
     address-family ipv6 unicast vrf VRF-BLUE autonomous-system 10
      !
      topology base
      exit-af-topology
      eigrp router-id 8.8.8.8
     exit-address-family
    
    R8#show run | sec ^vrf   
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
Host1#trace 2001:DB8:B::1
Type escape sequence to abort.
Tracing the route to 2001:DB8:B::1

  1 2001:DB8:A::2 3 msec 1 msec 1 msec
  2 2001:DB8:1::1 24 msec 24 msec 23 msec
  3 ::FFFF:10.3.0.2 [MPLS: Labels 103/609 Exp 0] 49 msec 48 msec 48 msec          « MPLS VPN Service Labael attached by PE R6
  4 ::FFFF:10.1.0.2 [MPLS: Labels 203/609 Exp 0] 49 msec 47 msec 49 msec
  5 ::FFFF:10.2.0.2 [MPLS: Labels 303/609 Exp 0] 49 msec 48 msec 48 msec
  6 2001:DB8:2::1 [MPLS: Label 609 Exp 0] 26 msec 27 msec 25 msec
  7 2001:DB8:2::2 48 msec 48 msec 47 msec
  8 2001:DB8:B::1 49 msec 51 msec 56 msec
 



R7#show eigrp address-family ipv6 vrf VRF-BLUE neighbors 
EIGRP-IPv6 VR(EIGRP-IPv6) Address-Family Neighbors for AS(10)
           VRF()
H   Address                 Interface              Hold Uptime   SRTT   RTO  Q  Seq
                                                   (sec)         (ms)       Cnt Num
0   Link-local address:     Gi0/1.10                 14 00:23:28  168  1008  0  4          « EIGRP IPv6 neighborship between PE - CE
    FE80::1




R7#show eigrp address-family ipv6 vrf VRF-BLUE topology  
EIGRP-IPv6 VR(EIGRP-IPv6) Topology Table for AS(10)/ID(7.7.7.7)
           Topology(base) TID(0) VRF(VRF-BLUE)
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
       r - reply Status, s - sia Status 

P 2001:DB8:A::/64, 1 successors, FD is 1310720
        via Connected, GigabitEthernet0/0.10
P 2001:DB8:B::/64, 1 successors, FD is 2621440                  « CE R7 receives EIGRP IPv6 prefix from PE R5
        via FE80::1 (2621440/1966080), GigabitEthernet0/1.10
P 2001:DB8:1::/64, 1 successors, FD is 1310720
        via Connected, GigabitEthernet0/1.10




R7#show ipv6 route vrf VRF-BLUE eigrp
IPv6 Routing Table - VRF-BLUE - 6 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
       B - BGP, HA - Home Agent, MR - Mobile Router, R - RIP
       H - NHRP, I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
       IS - ISIS summary, D - EIGRP, EX - EIGRP external, NM - NEMO
       ND - ND Default, NDp - ND Prefix, DCE - Destination, NDr - Redirect
       RL - RPL, O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1
       OE2 - OSPF ext 2, ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
       la - LISP alt, lr - LISP site-registrations, ld - LISP dyn-eid
       lA - LISP away, a - Application
D   2001:DB8:B::/64 [90/20480]               « EIGRP IPv6 prefix installed in RIB of CE R7 as internal route
     via FE80::1, GigabitEthernet0/1.10




R7#show ipv6 route vrf VRF-BLUE 2001:DB8:B::/64
Routing entry for 2001:DB8:B::/64
  Known via "eigrp 10", distance 90, metric 20480, type internal
  Route count is 1/1, share count 0
  Routing paths:
    FE80::1, GigabitEthernet0/1.10
      From FE80::1
      Last updated 00:25:55 ago
	  



R5#show eigrp address-family ipv6 vrf VRF-BLUE topology 2001:DB8:B::/64
EIGRP-IPv6 VR(EIGRP-IPv6) Topology Entry for AS(10)/ID(5.5.5.5)
           Topology(base) TID(0) VRF(VRF-BLUE)
EIGRP-IPv6(10): Topology base(0) entry for 2001:DB8:B::/64
  State is Passive, Query origin flag is 1, 1 Successor(s), FD is 0
  Descriptor Blocks:
  ::FFFF:6.6.6.6, from VPNv6 Sourced, Send flag is 0x0                « On PE R5 EIGRP route redistributed from BGP VPNv6
      Composite metric is (0/0), route is Internal (VPNv6 Sourced)
      Vector metric:
        Minimum bandwidth is 1000000 Kbit
        Total delay is 20000000 picoseconds
        Reliability is 255/255
        Load is 1/255
        Minimum MTU is 1500
        Hop count is 1
        Originating router is 8.8.8.8




R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64 
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 3
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 15360, localpref 100, valid, internal, best
      Extended Community: RT:65010:2 Cost:pre-bestpath:128:15360      « Route Target value attached by PE R6
        0x8800:32768:0 0x8801:10:512 0x8802:65281:2560 0x8803:65281:1500 
        0x8806:0:134744072 0x8807:45:822149120
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609
      rx pathid: 0, tx pathid: 0x0

Option 3) Configuring OSPFv3 between PE - CE

In the following scenario, MPLS 6VPE is configured with a single VRF connecting two IPv6 sites across an IPv4 MPLS network. The PE - CE routing protocol is OSPFv3. When configuring OSPF within a VRF and as the PE - CE routing protocol for a L3VPN network, it is important to add the command capability vrf-lite on the CE routers. This ensures functionality as a CE and proper handling of the DN bit when receiving routes from the PE.

OSPFv3 is also configured with a VRF on the PE routers, and redistribution happens between OSPFv3 and BGP on the PE routers which then advertise site specific IPv6 prefixes via BGP VPNv6 to the RR.

MPLS 6VPE configuration with PE - CE routing protocol OSPFv3 in VRF

Configuration:

R5 (PE)
    R5#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:1::1/64
     ospfv3 10 ipv6 area 0
     ospfv3 10 ipv6 network point-to-point
    
    
    R5#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.3.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
     
    R5#show run int Lo10 | sec int
    interface Loopback10
     ip address 5.5.5.5 255.255.255.255
    
    R5#show run | sec ^router
    router ospfv3 10
     !
     address-family ipv6 unicast vrf VRF-BLUE
      redistribute bgp 65010
      router-id 5.5.5.5
     exit-address-family
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 5.5.5.5
     network 5.5.5.5 0.0.0.0 area 0
     network 10.3.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 5.5.5.5
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute ospf 10
     exit-address-family
    
    R5#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:1
     !
     address-family ipv6
      route-target export 65010:1
      route-target import 65010:2
     exit-address-family
    
    R5#show run | sec ^mpls
    mpls label range 500 599
    
R6 (PE)
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R8 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R8 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:2::1/64
     ospfv3 10 ipv6 area 0
     ospfv3 10 ipv6 network point-to-point
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.5.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run | sec ^router
    router ospfv3 10
     !
     address-family ipv6 unicast vrf VRF-BLUE
      redistribute bgp 65010
      router-id 6.6.6.6
     exit-address-family
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 6.6.6.6
     network 6.6.6.6 0.0.0.0 area 0
     network 10.5.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute ospf 10
     exit-address-family
    
    R6#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:2
     !
     address-family ipv6
      route-target export 65010:2
      route-target import 65010:1
     exit-address-family
    
    R6#show run | sec ^mpls
    mpls label range 600 699
    
R7 (CE)
    R7#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host1 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:A::2/64
     ospfv3 10 ipv6 area 0
    
    R7#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R5 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R5 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:1::2/64
     ospfv3 10 ipv6 area 0
     ospfv3 10 ipv6 network point-to-point
    
    R7#show run | sec ^router
    router ospfv3 10
     !
     address-family ipv6 unicast vrf VRF-BLUE
      router-id 7.7.7.7
      capability vrf-lite
     exit-address-family
    
    R7#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
R8 (CE)
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host2 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:B::2/64
     ospfv3 10 ipv6 area 0
    
    R8#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R6 ** 
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R6 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:2::2/64
     ospfv3 10 ipv6 area 0
     ospfv3 10 ipv6 network point-to-point
    
    R8#show run | sec ^router
    router ospfv3 10
     !
     address-family ipv6 unicast vrf VRF-BLUE
      router-id 8.8.8.8
      capability vrf-lite
     exit-address-family
     
    R8#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
Host1#trace 2001:DB8:B::1
Type escape sequence to abort.
Tracing the route to 2001:DB8:B::1

  1 2001:DB8:A::2 2 msec 2 msec 2 msec
  2 2001:DB8:1::1 24 msec 25 msec 23 msec
  3 ::FFFF:10.3.0.2 [MPLS: Labels 103/610 Exp 0] 49 msec 49 msec 48 msec      « VPN Service Label assigned by PE R6
  4 ::FFFF:10.1.0.2 [MPLS: Labels 203/610 Exp 0] 48 msec 48 msec 50 msec
  5 ::FFFF:10.2.0.2 [MPLS: Labels 303/610 Exp 0] 48 msec 50 msec 49 msec
  6 2001:DB8:2::1 [MPLS: Label 610 Exp 0] 27 msec 27 msec 27 msec
  7 2001:DB8:2::2 49 msec 50 msec 49 msec
  8 2001:DB8:B::1 49 msec 48 msec 48 msec



R7#show ospfv3 vrf VRF-BLUE neighbor 

          OSPFv3 10 address-family ipv6 vrf VRF-BLUE (router-id 7.7.7.7)

Neighbor ID     Pri   State           Dead Time   Interface ID    Interface
5.5.5.5           0   FULL/  -        00:00:33    10              GigabitEthernet0/1.10       « OSPFv3 neighborship between PE - CE





R7#show ospfv3 vrf VRF-BLUE database

          OSPFv3 10 address-family ipv6 vrf VRF-BLUE (router-id 7.7.7.7)

                Router Link States (Area 0)

ADV Router       Age         Seq#        Fragment ID  Link count  Bits
 5.5.5.5         799         0x80000008  0            1           B E
 7.7.7.7         746         0x8000000D  0            1           None

                Inter Area Prefix Link States (Area 0)

ADV Router       Age         Seq#        Prefix
 5.5.5.5         541         0x80000002  2001:DB8:B::/64           « CE R7 receives Site 2 prefix as OSPF inter-area route

                Link (Type-8) Link States (Area 0)

ADV Router       Age         Seq#        Link ID    Interface
 5.5.5.5         799         0x80000002  10         Gi0/1.10
 7.7.7.7         746         0x80000002  10         Gi0/1.10
 7.7.7.7         746         0x80000002  9          Gi0/0.10

                Intra Area Prefix Link States (Area 0)

ADV Router       Age         Seq#        Link ID    Ref-lstype  Ref-LSID
 5.5.5.5         799         0x80000002  0          0x2001      0
 7.7.7.7         746         0x80000006  0          0x2001      0
 
 



R7#show ospfv3 vrf VRF-BLUE ipv6 database inter-area prefix 2001:DB8:B::/64

          OSPFv3 10 address-family ipv6 vrf VRF-BLUE (router-id 7.7.7.7)

                Inter Area Prefix Link States (Area 0)

  LS age: 604
  LS Type: Inter Area Prefix Links       « Site 2 prefix is an inter-area OSPF route
  Link State ID: 0
  Advertising Router: 5.5.5.5
  LS Seq Number: 80000002
  Checksum: 0x4F8E
  Length: 36
  Metric: 2 
  Prefix Address: 2001:DB8:B::
  Prefix Length: 64, Options: DN         « The DN bit is set when received from the PE router




R7#show ipv6 route vrf VRF-BLUE 2001:DB8:B::/64
Routing entry for 2001:DB8:B::/64
  Known via "ospf 10", distance 110, metric 3, type inter area
  Route count is 1/1, share count 0
  Routing paths:
    FE80::1, GigabitEthernet0/1.10
      From FE80::1
      Last updated 00:43:11 ago




R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 9
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 2, localpref 100, valid, internal, best
      Extended Community: RT:65010:2 OSPF ROUTER ID:6.6.6.6:0            « Route Target value attached by PE R6
        OSPF RT:0.0.0.0:2:0
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/610
      rx pathid: 0, tx pathid: 0x0

Option 4) Configuring RIPng between PE - CE

In the following example scenario RIPng is configured as the PE - CE routing protocol for a L3VPN MPLS 6VPE network. Two IPv6 sites are connected through a Service Provider MPLS network using a single VRF called "VRF-BLUE".

RIP Next Generation or RIPng is configured as the PE - CE routing protocol for an MPLS L3VPN 6VPE network

Configuration:

R5 (PE)
    R5#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R7 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R7 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:1::1/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R5#show run int Gi0/1 | sec int
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.3.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R5#show run int Lo10 | sec int
    interface Loopback10
     ip address 5.5.5.5 255.255.255.255
    
    R5#show run | sec ^ipv6 rip
    ipv6 rip vrf-mode enable
    
    R5#show run | sec ^ipv6 router|^router
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 5.5.5.5
     network 5.5.5.5 0.0.0.0 area 0
     network 10.3.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 5.5.5.5
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute rip RIPng-EXAMPLE
     exit-address-family
    ipv6 router rip RIPng-EXAMPLE
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute bgp 65010
     exit-address-family
    
    R5#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:1
     !
     address-family ipv6
      route-target export 65010:1
      route-target import 65010:2
     exit-address-family
    
    R5#show run | sec ^mpls
    mpls label range 500 599
    
R6 (PE)
    R6#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to CE R8 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to CE R8 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::1 link-local
     ipv6 address 2001:DB8:2::1/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R6#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to R1 **
     ip address 10.5.0.1 255.255.255.252
     ip ospf network point-to-point
     duplex auto
     speed auto
     media-type rj45
    
    R6#show run int Lo10 | sec int 
    interface Loopback10
     ip address 6.6.6.6 255.255.255.255
    
    R6#show run | sec ^ipv6 rip
    ipv6 rip vrf-mode enable
    
    R6#show run | sec ^ipv6 router|^router     
    router ospf 10
     mpls ldp autoconfig area 0
     router-id 6.6.6.6
     network 6.6.6.6 0.0.0.0 area 0
     network 10.5.0.0 0.0.0.3 area 0
    router bgp 65010
     bgp router-id 6.6.6.6
     bgp log-neighbor-changes
     neighbor 4.4.4.4 remote-as 65010
     neighbor 4.4.4.4 update-source Loopback10
     !
     address-family vpnv6
      neighbor 4.4.4.4 activate
      neighbor 4.4.4.4 send-community extended
     exit-address-family
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute rip RIPng-EXAMPLE
     exit-address-family
    ipv6 router rip RIPng-EXAMPLE
     !
     address-family ipv6 vrf VRF-BLUE
      redistribute bgp 65010
     exit-address-family
    
    R6#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 65010:2
     !
     address-family ipv6
      route-target export 65010:2
      route-target import 65010:1
     exit-address-family
    
    R6#show run | sec ^mpls
    mpls label range 600 699
    
R7 (CE)
    R7#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host1 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host1 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:A::2/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R7#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R5 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R7#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R5 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:1::2/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R7#show run | sec ^ipv6 router
    ipv6 router rip RIPng-EXAMPLE
     !
     address-family ipv6 vrf VRF-BLUE
     exit-address-family
    
    R7#show run | sec ^ipv6 rip   
    ipv6 rip vrf-mode enable
    
    R7#show run | sec ^vrf     
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
R8 (CE)
    R8#show run int Gi0/0 | sec int
    interface GigabitEthernet0/0
     description ** to Host2 **
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/0.10 | sec int
    interface GigabitEthernet0/0.10
     description ** to Host2 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:B::2/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R8#show run int Gi0/1 | sec int   
    interface GigabitEthernet0/1
     description ** to PE R6 ** 
     no ip address
     duplex auto
     speed auto
     media-type rj45
    
    R8#show run int Gi0/1.10 | sec int
    interface GigabitEthernet0/1.10
     description ** to PE R6 in VRF-BLUE **
     encapsulation dot1Q 10
     vrf forwarding VRF-BLUE
     ipv6 address FE80::2 link-local
     ipv6 address 2001:DB8:2::2/64
     ipv6 rip RIPng-EXAMPLE enable
    
    R8#show run | sec ^ipv6 rip       
    ipv6 rip vrf-mode enable
    
    R8#show run | sec ^ipv6 router
    ipv6 router rip RIPng-EXAMPLE
     !
     address-family ipv6 vrf VRF-BLUE
     exit-address-family
    
    R8#show run | sec ^vrf
    vrf definition VRF-BLUE
     rd 1:1
     !
     address-family ipv6
     exit-address-family
    
Host1#trace 2001:DB8:B::2
Type escape sequence to abort.
Tracing the route to 2001:DB8:B::2

  1 2001:DB8:A::2 2 msec 2 msec 2 msec
  2 2001:DB8:1::1 24 msec 24 msec 25 msec
  3 ::FFFF:10.3.0.2 [MPLS: Labels 103/609 Exp 0] 49 msec 49 msec 49 msec      « MPLS VPN Service Label assigned by PE R6
  4 ::FFFF:10.1.0.2 [MPLS: Labels 203/609 Exp 0] 48 msec 49 msec 48 msec
  5 ::FFFF:10.2.0.2 [MPLS: Labels 303/609 Exp 0] 48 msec 49 msec 48 msec
  6 2001:DB8:2::1 [MPLS: Label 609 Exp 0] 27 msec 27 msec 27 msec
  7 2001:DB8:2::2 48 msec 46 msec 48 msec



R7#show ipv6 rip vrf VRF-BLUE database 
RIP VRF "VRF-BLUE", local RIB
 2001:DB8:1::/64, metric 2
     GigabitEthernet0/1.10/FE80::1, expires in 165 secs
 2001:DB8:B::/64, metric 3, installed          « Site 2 IPv6 prefix learned by CE R7 through RIPng
     GigabitEthernet0/1.10/FE80::1, expires in 165 secs



R7#show ipv6 rip vrf VRF-BLUE next-hops 
RIP VRF "VRF-BLUE", Next Hops
  FE80::1/GigabitEthernet0/1.10 [2 paths]      « RIPng neighborship between PE - CE



R7#show ipv6 rip vrf VRF-BLUE           
RIP VRF "VRF-BLUE", port 521, multicast-group FF02::9, pid 48
     Administrative distance is 120. Maximum paths is 16
     Updates every 30 seconds, expire after 180
     Holddown lasts 0 seconds, garbage collect after 120
     Split horizon is on; poison reverse is off
     Default routes are not generated
     Periodic updates 56, trigger updates 3
     Full Advertisement 0, Delayed Events 0
  Interfaces:                                  « RIPng enabled on these CE R7 interfaces
    GigabitEthernet0/1.10
    GigabitEthernet0/0.10
  Redistribution:
    None



R7#show ipv6 route vrf VRF-BLUE rip
IPv6 Routing Table - VRF-BLUE - 6 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
       B - BGP, HA - Home Agent, MR - Mobile Router, R - RIP
       H - NHRP, I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
       IS - ISIS summary, D - EIGRP, EX - EIGRP external, NM - NEMO
       ND - ND Default, NDp - ND Prefix, DCE - Destination, NDr - Redirect
       RL - RPL, O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1
       OE2 - OSPF ext 2, ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
       la - LISP alt, lr - LISP site-registrations, ld - LISP dyn-eid
       lA - LISP away, a - Application
R   2001:DB8:B::/64 [120/3]                    « Site 2 route installed in RIB of CE R7
     via FE80::1, GigabitEthernet0/1.10




R7#show ipv6 route vrf VRF-BLUE 2001:DB8:B::/64
Routing entry for 2001:DB8:B::/64
  Known via "rip RIPng-EXAMPLE", distance 120, metric 3        « Site 2 route learned through RIPng
  Route count is 1/1, share count 0
  Routing paths:
    FE80::1, GigabitEthernet0/1.10
      From FE80::1
      Last updated 00:20:08 ago



R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 15
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 2, localpref 100, valid, internal, best
      Extended Community: RT:65010:2                           « PE R5 receives BGP VPNv6 route with Route Target assigned by PE R6
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609
      rx pathid: 0, tx pathid: 0x0

Information attached to BGP VPNv6 routes by different PE - CE routing protocols

IPv6 prefixes advertised from the CE routers to the PE routers are redistributed into the BGP VPNv6 address-family. The PE - CE protocol of choice may depend on a variety a circumstances and technical requirements. However, within the L3VPN MPLS 6VPE network the Site-specific prefixes are advertised as BGP VPNv6 routes. VPNv6 routes are 192-bits long as opposed to an IPv6 address which is 128-bit long.

The additional information contained in VPNv6 route advertisements may be different depending on the PE - CE routing protocol. The following table shows some of these differences.

BGP VPNv6 prefixes depending on PE - CE routing protocol
PE - CE Routing Protocol BGP VPNv6 Advertisement
External BGP (eBGP)
R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 3
Paths: (1 available, best #1, no table)
Flag: 0x100
  Not advertised to any peer
  Refresh Epoch 1
  65002
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin IGP, metric 0, localpref 100, valid, internal, best
      Extended Community: RT:65010:2
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609
      rx pathid: 0, tx pathid: 0x0
OSPFv3 for IPv6
R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 9
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 2, localpref 100, valid, internal, best
      Extended Community: RT:65010:2 OSPF ROUTER ID:6.6.6.6:0
        OSPF RT:0.0.0.0:2:0
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/610
      rx pathid: 0, tx pathid: 0x0
EIGRP IPv6
R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64 
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 3
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 15360, localpref 100, valid, internal, best
      Extended Community: RT:65010:2 Cost:pre-bestpath:128:15360
        0x8800:32768:0 0x8801:10:512 0x8802:65281:2560 0x8803:65281:1500 
        0x8806:0:134744072 0x8807:45:822149120
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609
      rx pathid: 0, tx pathid: 0x0
RIPng
R5#show ip bgp vpnv6 unicast rd 65010:2 2001:DB8:B::/64 
BGP routing table entry for [65010:2]2001:DB8:B::/64, version 15
Paths: (1 available, best #1, no table)
  Not advertised to any peer
  Refresh Epoch 1
  Local
    ::FFFF:6.6.6.6 (metric 5) (via default) from 4.4.4.4 (4.4.4.4)
      Origin incomplete, metric 2, localpref 100, valid, internal, best
      Extended Community: RT:65010:2
      Originator: 6.6.6.6, Cluster list: 4.4.4.4
      mpls labels in/out nolabel/609
      rx pathid: 0, tx pathid: 0x0